Wrought Iron and Ornamental Fence Company in Abilene, TX (Who Actually Call You Back)
A finished look from the street, in iron that keeps its line.
✔ Free on-site estimates
✔ On-site from start to finish
✔ Priority warranty scheduling
Open Monday to Saturday, 7am-7pm
Get Your Free Fence Estimate
Wrought Iron Fence Installation in Abilene
A wrought iron fence, also called an ornamental fence, frames your home and secures your yard in one line. Slim vertical bars keep your view and let the street see your landscaping. Gates and pickets add detail at the entrance. The look is formal, and the fence is tough.
At Everock Fencing in Abilene, TX, we install iron-style fence for homes and entrances across Taylor County. We set the posts straight, weld the joints clean and hang the gates true. Your fence looks sharp from the street on the first day and the tenth year.
Why Some Iron Fences Show Rust First
Iron holds its look while the finish holds. A scratch, a cut end or an open joint lets moisture in, and rust starts there.
We coat every cut and joint and set each post plumb, so the finish stays whole and the line stays sharp.
Why Wrought Iron Suits a Front Yard
Curb appeal that matches the house.
Give your home a front that looks finished. Iron lines frame brick and stone, and picket tops and panels add a clean, formal edge. Open bars keep the view while they mark the line.
A view that stays open.
You see the street, and the street sees your landscaping. Slim bars keep your sight lines and let light into the yard. The narrow gaps leave little to grip.
A higher limit at the street.
You get more fence where it counts. An open fence like this can stand taller at the front property line than a solid one. We check the exact limit with you before we set a post.
Strength with little wind load.
Your fence holds its line in a gust. Wind passes between the bars, so the posts carry less load than they would under a solid panel. Posts set deep keep the panels square.
Services That Go With a Wrought Iron Fence
Iron in Open Sun and Wind
An iron fence in Abilene lives in direct sun and open wind. A dark finish takes the sun’s heat, and gates take the brunt of daily use. Hinges and latches wear first because they move.
We build to match. We use a durable powder coat, touch up every weld and cut, and hang gates on heavy hinges. You get a fence that keeps its finish on the front line, where everyone sees it.
What Happens After You Get In Touch
Three steps, in this order. Nothing is hidden, and nothing starts until you approve the plan.
- You get in touch. Send the short form or call. We can call you back and ask a few questions first, so we know what you want to fence and where. Estimates are always free.
- We visit and quote in person. We walk your lot with you, measure each run and mark the gate spots. You choose the height, the picket style and the finish, and you see the itemized quote on site.
- We build, you approve. We request the Texas811 locate and set the posts in concrete. Then we fit the panels, hang the gates, align the latch and tidy the work area when we finish.
What the Job Covers From Start to Finish
Layout with you. We walk your lot, measure each run and mark the gate spots before any hole is dug.
Rules and lines. We check the layout against Abilene’s height and setback rules and request the Texas811 locate. That call does not mark private lines such as sprinklers, so you point those out on the visit.
Posts and caps. Posts go in concrete and are fitted with caps.
Panels. Powder-coated steel or aluminum panels in a wrought iron style are fitted along the line.
Gates. Walk gates and drive gates in a matching design are hung and the latch is aligned.
Picket Tops, Panels and Gate Styles
An iron fence is more than bars. A few design choices decide how it looks and how it works.
Flat top.
A clean top line that suits modern houses and low-maintenance yards.
Spear or picket top.
Pointed finials that add detail and a sharp top line.
Panel height.
Shorter panels frame a front yard. Taller panels secure a rear line or a side entry.
Ornamental details.
Scrolls, rings, finials and arched tops add detail to a plain run. They suit entrances and front lines.
Walk and drive gates.
Single or double gates sized for people or vehicles, hung to match the fence.
Powder-coated steel and aluminum in a wrought iron style are both common. Steel gives weight and strength. Aluminum gives a lighter panel that resists rust. We go through both at your estimate.
Panels and Posts That Hold the Line
Every part carries a load, so every part is picked for the job.
Posts.
They are set in concrete, sized to the panel height and the gate weight.
Panels.
Each panel is checked for square and bolted or welded to the posts with clean joints.
Finish.
Powder coat covers the metal. We touch up any scratch from handling or cutting.
Gate hardware.
Heavy hinges, a latch that meets its catch, and a stop that keeps the gate from swinging past its seat.
Caps.
A cap on every post keeps water out of the steel.
Height and Setback Rules for Iron Fence
An open iron fence gets different treatment from a solid one, and that works in your favor. Planning & Development Services handles placement, and Code Compliance handles condition.
A view kept at the front.
Open bars may reach 4 feet at the front property line. A solid fence there stops at 2½ feet.
Height that rises with the house.
The height may taper up to 7 feet at the front building line, the same cap that applies on the sides and rear.
A clean setback.
Posts sit 10 feet or more back from the curb or pavement edge, on your own land.
Paperwork that stays small.
Over 7 feet, a building permit and a variance come into play. At 7 feet or under, neither does.
Lines marked before the first hole.
Texas811 marks public lines for free. We make the request two working days ahead of the first post.
Habits That Keep Iron Looking Sharp
You can keep your iron fence sharp with a hose, a dab of paint and a drop of oil. Each step protects the finish.
Rinse it twice a year.
A hose clears dust and grime from the finish.
Touch up chips.
Cover any scratch with matching paint before rust can start.
Oil the hinges.
A drop on each hinge and the latch keeps gates quiet and easy.
Check the posts.
After a big storm, look for any post that moved.
Keep the base clear.
Sprinklers and soil against the bottom rail hold moisture. Pull them back a few inches.
Iron Fence Installation in Abilene and the Towns Around It
You get the same visit whether your lot is in Abilene or out toward Tye, Merkel, Buffalo Gap, Hawley or Clyde. Tell us where the lot sits, and we start with the rules for that address.
Price Factors for an Iron Fence
Panel height and the total length set most of the price. Steel or aluminum is the next factor, and then the top style and the number of gates. The site decides the rest: slope, hard digging, grade changes, and whether an old fence has to come out.
Estimates are always free. Quoting in person is the preferred way, because the measurements, the ground and the gate openings are all visible on site.
Seeing the job costs you nothing. Have three things ready: where the property line runs, where the gates go and the picket style you like.
Seeing the job costs you nothing. Bring three things: your entrance width, your gate wishes and the height you have in mind.
Iron, Aluminum or Wood at the Front
| What matters | Wrought iron style | Aluminum | Wood |
|---|---|---|---|
| View | Open bars | Open bars | Closed |
| Strength | Heaviest | Lighter | Depends on boards |
| Upkeep | Touch up chips | Rinse | Stain and sealer |
| Front line height | Taller, as an open fence | Taller, as an open fence | Lower, as a solid fence |
| Look | Formal, detailed | Slim, clean | Natural |
| Best for | Entrances and security | Lighter ornamental runs | Privacy |
Choose iron for a formal front and strong security. Choose wood when privacy matters most. See the wood fence installation page for a private rear line.
You Go First After Installation
You approve the height, the top style and the gate spots before we dig. Once work starts, the install is ours to get right.
After we build your fence, any fix goes to the front of the schedule. You’re booked first. If the problem is the installation, we fix it.
FAQs
How tall can an iron fence be in Abilene?
Along the sides and rear, up to 7 feet. At the front property line an open iron fence reaches 4 feet, and it can taper up to 7 feet at the front building line.
Is wrought iron real iron?
Many fences sold under that name are powder-coated steel or aluminum in a wrought iron style. We go through the options at your estimate.
What is the difference between wrought iron and ornamental fence?
Ornamental is the name for decorative metal fence, and wrought iron is the classic style of it. We go through the styles at your estimate.
Will it rust?
A powder coat protects the metal. Touch up chips early, and rust has no way in.
Can I add a gate later?
Yes. We can hang a walk gate or a drive gate in a matching style.
Do I need a permit for an iron fence?
Not when it stays at 7 feet or lower and meets the setbacks. Taller than 7 feet, a permit and a variance are needed.
How far from the street does it have to sit?
At least 10 feet from the curb or pavement edge, and outside the public right-of-way.
Who calls before digging?
We do. Texas811 wants two working days of notice, and marking public lines is free.
Do you build outside the Abilene city limits?
Yes. We build across Taylor County. The location of your lot decides which rules apply, and we check them before the build.
Do you charge for estimates?
No. Estimates are always free, and quoting in person is preferred.
Stand at the Entrance and Decide
Stand at your entrance with us and picture the finished fence. We measure the runs, mark the gates and talk through the top style and the height. The estimate is free, and you leave with a plan you can see.
Other Fences We Build
Fence Types
